The right insulated grocery bag should be selected according to the dimensions and loading pattern of the packed order, including any gel pack or ice pack. Instead of depending on a nominal litre rating, compare the filled package with the available flat-mailer dimensions or request a custom format. For chilled and frozen deliveries, closed-cell foam insulation, a separate coolant sleeve, and moisture protection provide a practical packaging solution.
Insulated grocery packaging must accommodate the products, coolant, and sealing area without excessive empty space. The available flat mailer sizes are 20 × 28 cm, 25 × 33 cm, 30 × 39 cm, and 35 × 45 cm. These formats can be used as starting points, while custom dimensions are available for specific order layouts.
For cold-chain applications, the insulation system uses closed-cell sponge foam inside a white PE outer film. This construction is intended for food, medicine, perishables, and other temperature-sensitive shipments transported with an ice pack. A dedicated gel-pack sleeve is recommended for chilled and frozen grocery orders because it keeps the coolant positioned separately from the products.
This product is a flat insulated mailer without a gusset. Three sides are welded, and the inner closed-cell foam layer helps slow heat transfer during transport. The mailer is supplied in a flat condition, which simplifies storage before packing and reduces the space required for fulfilment operations.
A permanent adhesive strip with a release liner and double-fold flap provides the closure. During packing, the operator can place the grocery order and coolant inside the mailer, remove the liner, and seal the package securely. Since the mailer has no stated litre capacity, the usable format should be confirmed using the packed product dimensions rather than an estimated volume.
The required insulation level depends on the product temperature range, route duration, coolant quantity, and delivery conditions. The available specification identifies closed-cell sponge foam as the insulating layer, but it does not provide a numerical insulation rating or a guaranteed temperature-holding time. These performance values should therefore be validated through a shipping trial for the intended route.
For a mixed grocery operation handling chilled, frozen, and ambient products, the broader last-mile solution can include a waterproof inner membrane. This layer helps contain condensation and thaw water. A colour-coded temperature band can also assist warehouse staff and drivers with sorting, handling, and routing orders according to their temperature category.
Buyers can request changes to the bag dimensions, film gauge, foam density, artwork, and adhesive-band position. Flexographic printing is available in one or two colours on the front panel. Outer film colour options include white, cool white, and black.
Customization is useful when products are loaded in a fixed arrangement or when the coolant must occupy a dedicated location. The final design should allow enough clearance for the packed groceries, gel pack, and closure area while avoiding unnecessary excess material.
| Decision area | Available option | Recommended application |
|---|---|---|
| Bag format and size | Flat, non-gusseted mailers measuring 20 × 28, 25 × 33, 30 × 39, or 35 × 45 cm | Match the selected size to the packed order; use a custom size for unusual loading patterns |
| Thermal layer | Closed-cell sponge foam beneath white PE film | Food, medicine, perishables, and cold-chain shipment protection |
| Coolant placement | Separate gel-pack sleeve | Chilled and frozen grocery orders that require controlled coolant positioning |
| Water management | Waterproof inner membrane | Deliveries where condensation or melted ice may occur |
| Sealing method | Permanent adhesive strip, release liner, and double-fold flap | Efficient flat-packed fulfilment and sealed temperature-sensitive shipments |
Quality management follows an ISO 9001:2015 system. Controls include incoming-material checks, inspections during production, and pre-shipment verification. Finished products are sampled using AQL procedures against the approved requirements. Laboratory testing can also be arranged when the buyer specifies the laboratory and requires shipment approval based on its report.
The insulated mailer has been used by a United States distributor for cold shipping at an annual volume of approximately 10 million pieces. Its reported purpose is to reduce heat transfer for fragile and perishable goods while taking up less storage and shipping space than rigid foam packaging.
Measure the packed grocery order, including the gel pack or ice pack and the space needed for sealing. Compare those measurements with the 20 × 28, 25 × 33, 30 × 39, and 35 × 45 cm flat-mailer options. Because no litre capacity is specified, custom sizing may be the better choice for a particular loading arrangement.
The construction includes a closed-cell sponge-foam inner layer. The supplied information does not state a quantified insulation value or holding-time guarantee. For chilled and frozen deliveries, the solution can add a dedicated gel-pack sleeve and a waterproof inner membrane for moisture control.
Yes. Available customization includes size, film gauge, foam density, print, and adhesive-band location. One- or two-colour flexographic printing can be applied to the front panel, with white, cool white, and black outer film choices. The mailers are packed flat and counted by carton.
Begin the selection process with the actual packed dimensions of the grocery order, then include the coolant and sealing requirements. Choose the listed flat-mailer size that provides a suitable fit, or request a custom size when the product arrangement does not match a standard format. For chilled or frozen grocery delivery, specify closed-cell foam insulation together with a dedicated gel-pack sleeve. Add a waterproof inner membrane when condensation or thaw water is expected.
Samples are typically available within 3 to 5 working days, while production generally takes 15 to 25 days after artwork approval. For technical guidance or a customized quotation, contact manager@ecoppack.com.
Huizhou Ecopack Packaging Products Co., Ltd. is a flexible packaging manufacturer based in Guangdong, China. Established in 2011, the company produces custom composite pouches and bags, including insulated mailers and thermal packaging, for customers in more than 40 countries. Its company information lists a factory area of over 10,000 square metres, production capacity exceeding 500,000 pouches per day, rotogravure and flexographic production lines, an ISO 9001:2015 Quality Management System, and FSC Chain of Custody certification.

REPORT