Before approving a large order of RGB laser projectors, buyers should evaluate the sample against the final application and documented specifications. The assessment should cover optical output, color wavelengths, beam quality, scanning accuracy, control interfaces, protection rating, safety behavior, continuous operation, aging results, packaging, and production consistency.
The projector uses an imported semiconductor solid-state laser with analog modulation. Available RGB power configurations are listed as 50W, 60W, and 80W. During sample approval, measure the real output of the red, green, and blue channels and compare the results with the configuration selected for the bulk order. The stated wavelengths are 636±5nm for red, 525±5nm for green, and 455±5nm for blue.
Examine the aperture and optical path for beam consistency. The published beam size is <8*9mm, while the specified divergence is <1.2mrad. Measurements should remain within the agreed specification during normal operation, effect changes, and extended use. Also watch for color shifts, unstable brightness, or visible distortion.
The scanning system is rated at 25KPPS high-speed scanning. Test geometric accuracy, movement smoothness, beam stability, and the repeatability of projected patterns. Include a continuous long-duration run in the inspection plan. This is particularly important for stage and rental applications where equipment may operate for many hours. A French stage production company has reported stable output and consistent effects during long-hour use of supplied lighting equipment, but each new sample should still be evaluated independently.
Connect the sample through its RJ45 and ILDA DB25 interfaces and test each advertised operating mode. The projector should respond reliably to ILDA, international DMX512, self-walk, and master-slave commands. Where relevant, confirm communication with Pangolin software and tiger, pearl, or MA controllers. Check effect selection, color control, scanning commands, and synchronization between linked units.
Safety behavior must be tested under realistic fault conditions. Disconnect or remove the control signal and confirm that the light shuts down as specified. Test the listed one-beam protection function and document the response time and operating condition for each test.
For outdoor projects, inspect the housing, seals, connectors, and cable entry points. Request the supplier's waterproof and safety test records supporting the IP66 claim. The documented quality process includes laser module inspection, optical performance verification, scanner testing, electronic component inspection, control system testing, aging testing, finished-product inspection, and pre-shipment checks. These records should be reviewed alongside the physical sample.
The projector is supplied in a flight case. Inspect the case, internal protection, accessories, connectors, manuals, and any items needed for immediate installation. Record the serial number and the exact sample configuration, then compare it with the quotation, technical data sheet, purchase order, and intended production version.
NewFeel Lighting holds CE certification for its laser light, certificate number UTT202406076C, with worldwide applicability listed. The company has also supplied RGB laser lights, fog machines, and special-effects equipment to a United States lighting equipment distributor serving wedding events, private parties, DJ performances, and small entertainment venues.
| Inspection Category | What to Measure or Test | Approval Requirement |
|---|---|---|
| Optical configuration | RGB power, wavelengths, analog modulation, beam size, and divergence | Measured performance matches the approved order specification |
| Scanning system | 25KPPS scanning, pattern accuracy, smooth movement, and effect stability | Effects remain stable during normal and extended operation |
| Control integration | ILDA, DMX512, self-walk, master-slave, RJ45, and ILDA DB25 | All required control methods operate correctly |
| Safety functions | One-beam protection and shutdown behavior after signal loss | Protection functions respond as documented |
| Outdoor readiness | IP66 construction, waterproof testing, and enclosure condition | Equipment is appropriate for the planned outdoor environment |
| Production consistency | Sample records, flight case, accessories, aging results, and inspection documents | Bulk production will follow the approved sample configuration |
Which optical values are most important during sample approval?
Check the selected 50W, 60W, or 80W RGB output, analog modulation, red, green, and blue wavelengths, beam size, and divergence. The stated reference values are 636±5nm red, 525±5nm green, 455±5nm blue, a beam size below 8*9mm, and divergence below 1.2mrad.
How can control compatibility be verified?
Use the intended control equipment to test ILDA, DMX512, self-walk, and master-slave operation through the available RJ45 and ILDA DB25 interfaces. Where required, confirm compatibility with Pangolin software and tiger, pearl, or MA controllers.
What should be checked before production is released?
Confirm the final configuration, test records, IP66 and safety documentation, aging results, accessories, and flight-case packaging. The listed minimum order quantity is one unit. Sample orders are stated at 7–15 working days, while bulk orders are listed at 20–35 working days after order confirmation. Customized laser systems depend on the selected configuration and project requirements. Technical consultation, setup and software configuration, installation assistance, troubleshooting, and spare-parts support are available.
A bulk purchase should be approved only after the sample passes optical, scanning, control, safety, waterproof, aging, and long-duration tests. Keep a written record of the measured configuration and use it as the production reference. Guangzhou New Feel Lighting And Audio Equipment Co., Ltd. combines R&D, manufacturing, sales, export, OEM/ODM, and customized lighting services, with a stated monthly capacity of approximately 5,000 professional lighting units. For technical solutions or product support, contact sunny@nfstagelight.com.
Guangzhou New Feel Lighting And Audio Equipment Co., Ltd., branded as NewFeel Lighting, was founded in 2008 in Guangzhou, China. The company manufactures stage lighting and special-effects equipment, including RGB laser projectors, outdoor laser projectors, moving head lights, fog machines, snow machines, and other professional effects products. Its equipment is used for concerts, festivals, weddings, clubs, entertainment venues, rental productions, and architectural lighting. The company maintains an R&D team focused on optical design, electronic control, structural improvement, and customized development, with factory output of approximately 5,000 or more lighting units per month. Its CE-certified laser products and industry cooperation experience support projects across multiple markets.

REPORT