Shower Door Sample Inspection: Essential Measurements and Glass Checks

A reliable Shower Door sample inspection begins with accurate field measurements and documented glass verification. Confirm that the item being reviewed is actually a Shower Door assembly, then record the opening size, panel dimensions, overall width and height, hardware locations, clearances, and edge condition. All results should be checked against the approved project drawings or technical specification.

Inspection Priorities

• Identify the sample as a Shower Door before creating or applying an inspection record. The available product information refers to a Standard Shower Set rather than a door assembly.
• Measure the finished opening, glass panel, total height, total width, hardware positions, and operating clearances. Include the measurement location, unit, and applicable project tolerance.
• Verify glass type, thickness, surface treatment, finish, edge processing, markings, and visible defects from the sample or approved supporting documents.
• Review hinge, handle, bracket, hole, swing, sliding, and contact clearances to ensure that the sample matches the intended installation.
• Keep records for bathroom or outdoor applications linked to the relevant project specification instead of relying on unrelated shower-system data.

Why the Existing Product Data Is Not Sufficient

The supplied record describes a Luxury Shower System with a Round Showerhead and Rough-In Valve in the Standard Shower Set category. It lists SKU DSRH01M08B81, a matte black finish, brass as the primary material, contemporary styling, three functions, a ceramic cartridge, and a height-adjustable handheld stand. These characteristics describe plumbing equipment and must not be treated as Shower Door glass or dimensional requirements.

The same record gives package dimensions of 38.2 inches wide, 17.72 inches deep, and 6.7 inches high, along with an item weight of 12 pounds. It also lists a 1.8 GPM flow rate for both the handheld and overhead shower. Package size and water-flow data cannot be used to approve a door panel, opening, or hardware layout.

Recommended Measurement and Glass Checklist

Dimensions and Installation Fit

Create a separate Shower Door inspection sheet. Measure the opening at the required points, including width and height variations, and record the panel dimensions, overall assembly size, hole locations, hardware positions, and installation clearances. Note whether the door is hinged, pivoting, or sliding, and compare swing or travel space, contact points, and fitting locations with the approved design.

Glass Verification

Confirm the glass type and thickness using a visible mark, supplier documentation, or written approval from the responsible technical source. Record any coating or treatment, surface finish, edge processing, corner condition, cut-outs, holes, chips, scratches, cloudiness, or other visible defects. If a value cannot be confirmed, mark it as unverified rather than estimating it from the Standard Shower Set record.

The supplied source does not include Shower Door glass thickness, glass type, treatment, panel tolerances, hole positions, hardware clearances, or glass test results. Those details must come from the physical sample, approved drawings, or project-specific technical documentation.

Source Data Compared With Required Checks

Frequently Asked Questions

Conclusion and Product Support

Complete the Shower Door sample record with measured opening and panel dimensions, hardware locations, installation clearances, edge conditions, and confirmed glass information. Keep these findings separate from the Standard Shower Set data, because the plumbing record does not establish Shower Door compliance.

Modland Inc lists a minimum order quantity of 1. Overseas stock products can be shipped within 2 days after stock preparation, while customized products generally require 45–60 days. Its quality controls include raw-material inspection, manufacturing-process inspection, finished-product testing, and installation acceptance. The company also states that replacement parts are provided free of charge during the 1-year warranty period. The cUPC Product Listing Certification, certificate MC-13485, and NSF Listing of Safe Drinking Water Products certificate C0044104 support the listed plumbing products and should not be interpreted as certification of Shower Door glass. For technical assistance, contact info@mod-land.com.

About Modland Inc

Modland Inc is a global bathroom vanity manufacturer and project solution provider serving builders, contractors, and developers through US local stock supply and factory-direct production. Established in 2016, the company develops bathroom cabinets, showers, faucets, and related products. Its main market is the United States, with production bases in the United States and Malaysia, more than 10 US warehouses, and local showroom support. Listed credentials include the cUPC Product Listing Certification, certificate MC-13485, and the NSF Listing of Safe Drinking Water Products, certificate C0044104.