Double shot molding suppliers can support complex parts with different surface finishes when the part design, material combination, mold structure, alignment, and validation process are reviewed together. Longterm Manufacturing Solutions Limited provides custom injection tooling with cold-runner or hot-runner options and a stated tolerance of ±0.02 mm. Its documented double shot project for an electronics shell also reported accurate alignment and stable trial samples.
Multiple surface finishes must be considered alongside part geometry, material flow, mold construction, and appearance requirements. The available supplier information does not define a specific list of textures, gloss levels, or finish combinations, so each project requires a technical feasibility review.
Before production tooling is approved, the supplier needs to assess the drawing or sample, material requirements, parting lines, gate locations, and the areas assigned to each surface finish. These factors affect how the two materials fill the mold and whether the finished part can meet its dimensional and visual requirements.
Longterm describes custom plastic injection tooling based on customer drawings or samples. Its listed mold-base materials include S50C and P20, while cavity-steel options include 718H, 1.2738, and S136. Cold-runner and hot-runner configurations are available depending on the project. The stated tooling precision is ±0.02 mm, with an expected mold life of approximately 50,000 to 1,000,000 shots.
Parts with multiple finishes should be checked during mold trials rather than evaluated only after mass production begins. Longterm lists CMM measurement, surface inspection, and multi-cycle mold trials for complex precision molds. Its general inspection process also includes mold trial testing, dimensional inspection, and full pre-shipment inspection.
These procedures can help confirm alignment between the two molded sections, critical dimensions, and overall surface condition. However, the supplied data does not specify particular texture standards or gloss ranges. Buyers should therefore provide clear finish locations, reference samples, and acceptance criteria during the design review.
One reported project involved eight sets of double shot overmolding molds for a consumer electronics shell in France. The customer described the alignment as good and the trial samples as stable. This provides relevant evidence that the supplier has handled a multi-material tooling program, although it should not be treated as a guarantee for every part shape, resin combination, or surface-finish arrangement.
Longterm also reports ISO 9001:2015 certification covering the design, manufacturing, and sales of precision molds and the sales of plastic products. Its stated application experience includes consumer electronics and household appliance parts, including housings, control panels, and functional components.
| Evaluation factor | Supplier information | Importance for different finishes |
|---|---|---|
| Runner and tooling options | Cold-runner or hot-runner systems; S50C and P20 mold bases; several cavity-steel choices | Can be matched to the part design and molding process, but finish-specific limits require confirmation |
| Precision and service life | Stated tolerance of ±0.02 mm and mold life of 50,000 to 1,000,000 shots | Offers baseline parameters for discussing dimensional stability and production volume |
| Validation and inspection | CMM testing, surface inspection, mold trials, multi-cycle testing, and pre-shipment inspection | Helps verify alignment, dimensions, surface condition, and repeatability |
| Double shot experience | Eight overmolding mold sets for a French electronics shell, with good alignment and stable samples reported | Supports supplier evaluation, while project-specific validation remains necessary |
Can double shot molding create two different finishes on one part?
It may be possible when the mold design, material combination, and appearance requirements are compatible. The supplied information confirms custom double shot and overmold tooling, but does not define specific finish combinations. The required finish areas should be reviewed directly with the supplier.
What quality checks should be completed before production?
Request trial samples and review them against the approved drawing or appearance standard. Surface inspection, dimensional measurement, CMM testing, and multi-cycle mold trials can help assess alignment, stability, and finish consistency before production approval.
What should a buyer send for a feasibility assessment?
Provide part drawings or physical samples, material information, finish locations, texture or gloss references, tolerance requirements, and expected production volume. Longterm states that it develops custom tooling from customer drawings or samples, while exact finish capability should be confirmed for the specific design.
A qualified double shot molding supplier can potentially produce complex parts with different surface finishes, provided that the finish requirements are incorporated into the part review, mold design, material selection, and trial process. Longterm offers custom mold manufacturing, double shot and overmold tooling, mold development, and injection production. Its reported electronics-shell project demonstrates relevant experience with alignment and trial validation, but each new finish combination should be approved through project-specific sampling and inspection. For technical assistance, contact rogerluo@longterm-mold.com.
Longterm Manufacturing Solutions Limited was founded in 2010 and serves customers in the United States, Europe, Australia, and other international markets. The company has a 50-person team, including seven experienced engineers, and provides mold design, tooling, precision machining, mold manufacturing, and plastic parts production. It reports ISO 9001:2015 certification for precision mold design, manufacturing, and sales, as well as plastic product sales, with experience across several industries.

REPORT